Question: What causes a chainsaw chain to break?

If the chain is too tight or too lose it can cause a chain break. Because heat causes the bar and chain to expand. If you do it while the chain is hot, it could be too tight when the chain is cooled down and can damage the bar. So tension a chainsaw whenever it is cooled down.

How long is a chainsaw chain supposed to last?

The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.

How do you keep a chainsaw from breaking?

0:070:59Chainsaw - Chain Break - YouTubeYouTubeStart of suggested clipEnd of suggested clipIts always a good idea to always keep two hands on the saw so to properly engage the chain break weMoreIts always a good idea to always keep two hands on the saw so to properly engage the chain break we have a couple techniques. That you can use the first is called the wrist roll.

Can a broken chainsaw chain be fixed?

If the chain itself has broken teeth or does not fit back into the rails once it has come off, it will likely need to be replaced. Some chains can be repaired from this type of damage with a flat file.

What happens if you over tighten a chainsaw chain?

By tightening the chain too much, youre putting extreme stress on the drive sprocket and bar nose which will result in premature wear. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw.

When should you throw away a chainsaw chain?

Chainsaw feels unbalanced, cuts unevenly, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesnt cut correctly- then you need to replace the chain.

Can you run a chainsaw without a chain brake?

Although theyre prohibited from sale, chainsaws without a chain brake can still be used by their owners, and service agents can still repair them at the request of their customers. However, chainsaws without a chain brake cant be offered for sale or supplied to anyone else.

How do you know when to replace a chainsaw bar?

Common signs that indicate it is time to replace the chainsaw bar are:Damaged or Bent bar.Chain wiggles side to side on the bar.The edges of blades are tilted at an angle.A jammed or damaged bar nose sprocket.

How much tension should be on a chainsaw chain?

I like to pull on the chain for a reference. It should give about a 1/4 inch from the bar without much effort. Finally, while still holding up on the tip of the bar, tighten the bar nuts. Proper chainsaw chain tension is safer, it cuts better and it will extend the life of both your chainsaw and your chain.

How tight should you make a chainsaw chain?

The chainsaw chain should feel snug but still pull freely. Finally, perform a snap test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.

How do you tell when a chainsaw chain is worn out?

There are several signs that show if your chainsaw chain is worn out:The Chain Comes Off the Bar easily.There is smoke.Some teeth are missing.The chainsaw chain is chipped.A lot of rust.You cannot cut through wood as well as you would have expected.The Chainsaw Has a Shaky Performance.

Can you start a chainsaw with the brake on?

The chain brake should be activated when you start the chainsaw. Many chainsaw models can be started in what is known as half-throttle position. In this position, the chain can rotate – if the chain brake is not activated.

Can I use a chainsaw to cut through ice?

Yes, you can cut ice with your chainsaw. You dont have to apply any mineral oil to prevent the water from pollution. To prevent the blade from rusting, you will have to look after your chainsaw.

Should you flip your chainsaw bar?

Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear. This reduces a chainsaws ability to cut accurately.

How often should you replace chainsaw chain?

Chainsaw durability differs from one item to another, although all the tools become dull over time. However, most top-quality chains can last up to 5 years of extensive use, or up to a decade when used occasionally. Additionally, these tools durability is highly dependent on maintenance.

Join us

Find us at the office

Koslowski- Malnick street no. 74, 79723 Yamoussoukro, Côte d'Ivoire

Give us a ring

Pricsilla Furch
+95 159 418 263
Mon - Fri, 7:00-22:00

Write us